Kovové a plastické kontejnery

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 393 (Equipment for storage tanks and for service stations)
Původce: CEN
K připomínkám do: 20.11.2018
Zobraz více Zobraz méně
 

This document applies to metering pumps, dispensers and remote pumping units to be installed at liquid fuel filling stations, designed to dispense flammable liquid fuels into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min-1, and intended for use and storage at ambient temperatures between −20 °C and +40 °C. Measures in addition to those required by this European Standard might be required for use and storage at temperature outside this range. The need for and nature of additional requirements should be determined by the manufacturer, if necessary after consulting the client.

This document deals with all significant hazards, hazardous situations and events relevant to metering pumps, dispensers and remote pumping units, when they are used as intended and under the conditions foreseeable by the manufacturer (see Clause 4).

This document gives health and safety related requirements for the selection, construction and performance of the equipment.

This document does not deal with noise and with hazards related to transportation and installation.

This document does not include any requirements for metering performance.

Vapour recovery efficiency rates are not considered within this European Standard.

Fuels other than the ones of Explosion Group IIA are excluded from this European Standard.

This document is not applicable to metering pumps, dispensers and remote pumping units which are manufactured before the date of publication of this document by CEN.

This document does not apply to equipment for use with liquefied or compressed gases.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 393 (Equipment for storage tanks and for service stations)
Původce: CEN
K připomínkám do: 20.11.2018
Zobraz více Zobraz méně
 

This document specifies safety requirements for the construction and performance of safe breaks to be fitted to metering pumps and dispensers installed at filling stations and used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min-1.

This document applies to fuels of Explosion Group IIA and also aqueous urea solution according to ISO 22241‑1.

NOTE          Fuels other than of Explosion Group IIA are excluded from this European Standard.

The requirements apply to safe breaks at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range.

This document pays particular attention to electrical, mechanical and hydraulic characteristics of, and electrical apparatus incorporated within or mounted on, the safe break.

This document applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This document also addresses electrical and mechanical hazards.

This document does not apply to equipment dispensing compressed or liquefied gases.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 393 (Equipment for storage tanks and for service stations)
Původce: CEN
K připomínkám do: 20.11.2018
Zobraz více Zobraz méně
 

This document specifies safety requirements for the construction and performance of swivels to be fitted to delivery hose assemblies on metering pumps and dispensers installed at filling stations and used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min-1. It pays particular attention to electrical, mechanical and hydraulic characteristics of swivels.

This document applies to fuels of Explosion Group IIA and also aqueous urea solution in accordance with ISO 22241‑1.

NOTE 1       Fuels other than of Explosion Group IIA are excluded from this European Standard.

The requirements apply to swivels at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range.

This document applies mainly to hazards related to the ignition of liquid fuels being dispensed or their vapour. This document also addresses electrical and mechanical hazards of swivels.

This document does not apply to equipment dispensing compressed or liquefied gases.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 393 (Equipment for storage tanks and for service stations)
Původce: CEN
K připomínkám do: 20.11.2018
Zobraz více Zobraz méně
 

This document specifies safety and environmental requirements for the construction and performance of shear valves to be fitted to metering pumps, dispensers, and/or satellite delivery systems installed at petrol filling stations and used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers at flow rates up to 200 l · min-1.

This document applies to fuels and their vapours of Explosion Group IIA, and also aqueous urea solution according to ISO 22241‑1.

NOTE 1       Fuels other than of Explosion Group IIA are excluded from this document.

The requirements apply to shear valves at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range.

This document pays particular attention to mechanical and hydraulic characteristics.

This document does not apply to equipment dispensing compressed or liquefied gases.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 393 (Equipment for storage tanks and for service stations)
Původce: CEN
K připomínkám do: 27.11.2018
Zobraz více Zobraz méně
 

Scope

This document specifies safety and environmental requirements for the construction and performance of nozzles to be fitted to metering pumps and dispensers installed at filling stations and which are used to dispense liquid fuels and aqueous urea solution into the tanks of motor vehicles, boats and light aircraft and into portable containers, at flow rates up to 200 l · min-1.

This document applies to fuels of Explosion Group IIA and also aqueous urea solution according to ISO 22241‑1.

NOTE          Fuels other than of Explosion Group IIA are excluded from this document.

The requirements apply to automatic nozzles dispensing flammable liquid fuels at ambient temperatures from –20 °C to +40 °C with the possibility for an extended temperature range.

This document does not apply to equipment dispensing compressed or liquefied gases.

This document does not include any requirements for metering performance, such as might be specified under the Measuring Instruments Directive, nor those requirements specified under the Electromagnetic Compatibility Directive.

Vapour recovery efficiency rates are not covered in this document.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 266 (Thermoplastic static tanks)
Původce: CEN
K připomínkám do: 3.12.2018
Zobraz více Zobraz méně
 

This document specifies the product characteristics and the corresponding test methods for static thermoplastic tanks made of:

—    blow moulded polyethylene, or

—    rotationally moulded polyethylene, or

—    rotationally moulded anionically polymerized polyamide 6,

with or without factory assembled reinforcement.

The products covered by this European Standard:

—    are intended to be used for internal or external installations, for above ground storage of fuels limited to kerosene, heating oil, diesel, fatty acid methyl ester (FAME) and bioliquids (containing up to 15 % FAME);

—    have a maximum filling capacity from 400 l up to and including 10 000 l, except for those made of anionically polymerized polyamide 6 where the maximum filling capacity will be limited to 3 000 l;

—    are subject to atmospheric pressure but not to any external loading (e.g. installation, wind and snow, earthquakes, flooding);

—    are not manufactured using recycled thermoplastic material;

—    are not manufactured using regrind thermoplastic material for rotationally moulded tanks;

—    are not manufactured using more than 50 % of regrind thermoplastic material for blow moulded tanks.

This document does not include tanks for the transport and distribution of fuels or gasses, or tanks for the storage of gas.

Flammable fuels with a flash point > 55 °C as determined by EN ISO 2719:2016 are eligible for storage in the tanks described in this standard without further provisions.

Flammable fuels with a flash point ≤ 55 °C as determined by EN ISO 2719:2016 are also eligible for storage in the tanks described in this standard if the provisions concerning electrostatic behaviour according to CLC/TR 60079‑32‑1:2015 are fulfilled.

Oblast zaměření: Kovové a plastické kontejnery
Komise : CEN/TC 226 (Thermoplastic static tanks)
Původce: CEN
K připomínkám do: 3.12.2018
Zobraz více Zobraz méně
 

This document specifies requirements for new traffic cones and new traffic cylinders with retroreflective properties.

This document specifies minimum essential visual and physical performance characteristics; test methods for determination of product performance and the means by which this performance may be communicated to the user and the public including safety enforcement agencies.

The document provides a series of categories or classes by which a traffic cone or traffic cylinder may be specified for use in different applications in accordance with best practice.

In the case of physical properties, performance levels and indicative tests are provided for cold weather, stability, and impact resistance when dropped. Requirements for visual recognition properties, colour, retro-reflectivity and luminance are provided.

Provision for identification and marking to declared levels of performance is provided.

There are other product shapes which perform similar functions. This document does not cover devices made in other shapes, or which do not meet the design requirements of this document.